Two products carry the name "cattle panel", and a buyer asking for one sometimes needs the other. One is a welded wire grid you lean on a fence line or drag across a paddock for a temporary break. The other is a tube panel with five to seven horizontal rails, built to take a shoulder from an animal that has decided to go elsewhere. Very different load.
Knot types and horse aperture have their own pages. The question here is narrower: what does a crowd of 500 to 700 kg animals put into a panel, and which construction answers it.
What a Herd Actually Loads Onto a Panel
A welded mesh cattle panel is plain drawn wire laid on a grid, resistance welded at every crossing, then hot-dip galvanised as a finished sheet. Line wires run 4 to 6 mm across a 150 x 150 mm or 150 x 300 mm opening. Dipping after welding is the point: the weld nugget goes into the bath with everything else, so there is no uncoated spot on the sheet.
A corral panel works the other way round. Tube - 42 mm round, or an oval around 30 x 45 mm - is saddle-welded into uprights, usually with a one-piece bowed vertical at each end so the panel stands without a post. The tube arrives galvanised from the mill. Every saddle weld burns that coating off and leaves a ring of bare steel. Panels are not re-dipped afterwards. That ring rusts two seasons before anything else on it.
On rail profile, ignore the sales pitch. At equal wall thickness an oval rail and a round one of similar mass sit within a few per cent of each other in bending, so "oval is stronger" is marketing. What oval buys is a wider face to weld against and a smoother surface for a hide to slide along. Good reasons. Strength is not one.
Now the load, where the two products part company. One 600 kg animal leaning on a rail puts 1.5 to 2 kN into the panel at rail height, and a mesh panel built for pasture shrugs that off. A crowding alley is not that. Ten animals with nowhere to go surge together and the same panel sees two to three times the figure, arriving as impact. Light-gauge mesh bulges permanently on the first busy day. Not a defect in the mesh - the wrong product in the wrong place.
Tube panels answer crowd load with wall thickness and rail count. A third lever gets missed: length. A 2.4 m panel is stiffer than a 3.0 m panel of the same tube, because deflection under a point load climbs with the cube of span. In a loading race take the short panel and accept the extra pins.
Picking by Animal and Job, Not by Price
Start with the animal and what it does when frightened, then work back to a spec. A panel specified from a price list holds calm cattle and fails on the afternoon the herd runs.
Height first. 1.5 m contains settled beef cattle and nothing more; a bull or an excited yearling clears it without much effort, so working pens get 1.8 m. At the other end, a 150 mm grid will not hold pigs or goats - a 30 kg piglet walks straight through, and a goat climbs a mesh panel because the horizontal wires are a ladder. Mesh cattle panels are a cattle product.
| Job | Panel type | Height x length | Wire or tube | Approx. weight | Fails by |
|---|---|---|---|---|---|
| Pasture subdivision | Welded mesh cattle panel | 1.5 m x 2.4 m | 4.0-5.0 mm wire, 150 x 300 mm | 11-14 kg | Torn loose from a driven post |
| Temporary paddock, 16 ft run | Welded mesh cattle panel | 1.27 m x 4.88 m | 5.0 mm wire, 150 x 150 mm | 17-20 kg | Buckles flat if used as a gate |
| Holding pen, feedlot | Six-rail tube corral panel | 1.8 m x 3.0 m | 42 mm round or 30 x 45 mm oval, 2.0 mm wall | 42-48 kg | Rusts at the saddle welds first |
| Crowd alley, squeeze, loading race | Six-rail heavy corral panel | 1.8 m x 2.4 m | 42 mm round, 2.5 mm wall, centre brace | 45-52 kg | Bends at mid-span under a surge |
| Bull pen, quarantine | Seven-rail tube corral panel | 1.8 m x 2.4-3.0 m | 42 mm round, 2.0-2.5 mm wall, tighter bottom spacing | 48-56 kg | Top rail takes the hit if height is short |
| Calving pen | Mesh panel, reduced bottom spacing | 1.5 m x 2.4 m | 4.0-5.0 mm wire, 100 mm near the base | 13-16 kg | Newborn calves slip through a 150 mm grid |
Weights are nominal for the sizes shown and will move with wire tolerance, tube wall tolerance and rail count. Ask for weighed figures on the exact configuration you are buying.
Two details decide whether a portable corral survives its first year, and neither is on a spec sheet. Connection first: drop pins are quick and rattle loose in hard service, two-bolt clamps stay tight. Move a pen once a season and pins are fine; reconfigure a race weekly and buy clamps. Then the foot - bare tube sinks 30 to 50 mm into soft ground after a week of rain, one corner drops and the whole run racks out of square. A foot plate costs little and ends the monthly re-levelling.
Bundles, Containers and Standing Panels on Real Ground
Freight on panels is a volume problem pretending to be a weight problem. A 20GP carries about 22 tonnes of payload and you run out of floor space long before that. Mesh panels nest flat, so a box takes roughly 350 to 450 pieces. Six-rail tube panels do not nest at all and land nearer 180 to 240. Get the count from your forwarder before pricing a job per metre.
Bundling matters more on the tube product. Rails bear on rails through a strap, and on a long sea leg that contact rubs the zinc off, so you meet bright steel at the port. Two straps minimum, corner protectors under each, dunnage between bundles. Mesh panels are forgiving in transit and less so on site: leave a bundle on wet ground a month and rust blooms press into the crossings.
In service, the bottom rail goes first. It lives in the wettest, most corrosive band of the assembly - standing water, urine, packed manure - while the top rail stays dry for a decade. That band is the only place worth spending extra on: heavier wall, welded end caps instead of push-in plastic, a few centimetres of clearance. Expect 15 to 25 years from a dipped mesh panel inland, 12 to 15 from a tube panel whose welds were never recoated, and half either figure on a coastal yard.
Wind catches a 3.0 m panel run harder than most buyers expect, and a portable system has no concrete in it. Two ground stakes per panel on any run past 20 m, or the line walks. More panels are bent in storage than in service.
Will a mesh cattle panel work in a crowding alley?
No. Use a six-rail tube panel at 2.4 m long with at least 2.0 mm wall. Mesh is built for animals that lean, not a crowd that surges, and a bulge narrows the race where cattle already hesitate.
Is 1.5 m tall enough for a bull?
Not on its own. Go to 1.8 m and tighten the lower spacing on a mesh panel, because a bull tests a fence with its head and shoulders before it tries to jump. A 1.5 m panel around a bull is a fence you will repair.
Can I use cattle panels for pigs, goats or sheep?
Pigs and goats, no. A 150 mm opening passes a piglet, and a goat treats the horizontal wires as a ladder. Sheep sit somewhere in between - they respect a mesh panel better than goats do, but lambs find the bottom corner. Order panels specified for the species.
What galvanising should I ask for on tube panels?
Specify the coating, not just "galvanised". Pre-galvanised tube typically runs 60 to 90 g/m2, and you should ask what the welds get - usually nothing. Panels dipped after welding cost more and remove the problem; if the budget will not stretch, allow for cold-galvanising the welds on arrival.
How many panels do I need for a round pen?
Divide the circumference by the panel length and add one for the gate. A 15 m diameter pen is about 47 m around, so roughly 16 panels at 3.0 m or 20 at 2.4 m - and the short ones give a stiffer wall. Order a spare; you will bend one.
Can I mix both types in one container?
Yes, and it usually makes sense - mesh for the paddock, tube for the working pens, one shipment. Load the tube panels first against the front bulkhead and the mesh bundles on top, not the other way round, or the flat sheets carry the weight of the rails.
Tell us the animal and the job, not just a panel size: species, head count, pen dimensions, whether there is a crowd alley, how often the layout moves. We build both types in Anping - mesh panels dipped after welding, corral panels in 42 mm round or oval tube with five to seven rails - and ship them in one container with pins, clamps, feet and gate panels. Write to sales@tengshanmetal.com with the layout and we will quote panels, hardware and a container count together.
